Search for parts and brands:

model, engine code, part number etc.

Home » Parts » Piston Rings Listing » RING SET - E1C-B1446020 - 89.00MM

RING SET - E1C-B1446020 - 89.00MM

Rings made with a combination of strength, rigidity and value for money.



Product Details

A piston ring must provide a predictable and positive radial fit between the cylinder wall and the running surface of the piston ring for an efficient seal. The radial fit is achieved by the inherent pressure of the piston ring. The piston ring must also maintain a seal on the piston ring lands.

In addition to inherent pressure, a piston ring seals the combustion chamber through applied pressure. Applied pressure is pressure applied from combustion gases to the piston ring, causing it to expand. Some piston rings have a chamfered edge opposite the running surface. This chamfered edge causes the piston ring to twist when not affected by combustion gas pressures.

Another piston ring design consideration is cylinder wall contact pressure. This pressure is usually dependent on the elasticity of the piston ring material, free piston ring gap, and exposure to combustion gases. All piston rings used by Briggs & Stratton engines are made of cast iron. Cast iron easily conforms to the cylinder wall. In addition, cast iron is easily coated with other materials to enhance its durability. Care must be exercised when handling piston rings, as cast iron is easily distorted. Piston rings commonly used on small engines include the compression ring, wiper ring, and oil ring.

Compression Ring

The compression ring is the top or closest ring to combustion gases and is exposed to the greatest amount of chemical corrosion and the highest operating temperature. The compression ring transfers 70% of the combustion chamber heat from the piston to the cylinder wall. Most Briggs & Stratton engines use either taper-faced or barrel-faced compression rings. A taper faced compression ring is a piston ring that has approximately a 1° taper angle on the running surface. This taper provides a mild wiping action to prevent any excess oil from reaching the combustion chamber.

A barrel faced compression ring is a piston ring that has a curved running surface to provide consistent lubrication of the piston ring and cylinder wall. This also provides a wedge effect to optimize oil distribution throughout the full stroke of the piston. In addition, the curved running surface reduced the possibility of an oil film breakdown due to excess pressure at the ring edge or excessive piston tilt during operation.

The compression ring, sometimes called the scraper ring, Napier ring, or back-up wiper ring, is the next ring away from the cylinder head on the piston. The wiper ring provides a consistent thickness of oil film to lubricate the running surface of the compression ring. Most wiper rings in Briggs & Stratton engines have a taper angle face. The tapered angle is positioned toward the oil reservoir and provides a wiping action as the piston moves toward the crankshaft.

The taper angle provides contact that routes excess oil on the cylinder wall to the oil ring for return to the oil reservoir. A compression ring incorrectly installed with the tapered angle closest to the compression ring results in excessive oil consumption. This is caused by the wiper ring wiping excess oil toward the combustion chamber.

Oil Ring

An oil ring includes two thin rails or running surfaces. Holes or slots cut into the radial center of the ring allow the flow of excess oil back to the oil reservoir. Oil rings are commonly one piece, incorporating all of these features. Some on-piece oil rings utilize a spring expander to apply additional radial pressure to the piston ring. This increases the unit (measured amount of force and running surface size) pressure applied at the cylinder wall.

The oil ring has the highest inherent pressure of the three rings on the piston. Some Briggs & Stratton engines use a tree-piece oil ring consisting of two rails and an expander. The oil rings are located on each side of the expander. The expander usually contains multiple slots or windows to return oil to the piston ring groove. The oil ring uses inherent piston ring pressure, expander pressure, and the high unit pressure provided by the small running surface of the thin rails.

The piston acts as the movable end of the combustion chamber and must withstand pressure fluctuations, thermal stress, and mechanical load. Piston material and design contribute to the overall durability and performance of an engine. Most pistons are made from die- or gravity-cast aluminum alloy. Cast aluminum alloy is lightweight and has good structural integrity and low manufacturing costs. The light weight of aluminum reduces the overall mass and force necessary to initiate and maintain acceleration of the piston.